Specific gravity (SG) is the ratio of a material's density to that of water. Quartz has an SG of 2.65, so a given volume of solid quartz weighs 2.65 times the same volume of water. Sulphide minerals are denser, and gold far denser.
The mass of a powdered ore sample is readily weighed, so measuring its SG is a matter of determining its volume. A pycnometer is a small glass flask with a stopper that holds the same volume each time it is filled. The powder displaces its own volume of water, and careful weighing gives that volume and therefore the SG.
An error in SG carries through to pulp densities, flows, residence times and inventories across the whole plant. This article gives the standard water pycnometer method, the calculation, the common errors and a check from plant pulp samples.
Applications of specific gravity in the plant
SG is used to convert pulp density to percent solids, and hence slurry flows to dry tonnes; see the pulp density calculator. It determines slurry volume flow and therefore residence time in leach tanks and flotation cells, and it enters gold-in-circuit and other inventories calculated from tank volumes.
It also affects cyclone sizing, since denser solids give a finer cut, as well as mill power and charge density, and pump and pipeline design.
The water pycnometer method
- Dry a representative split at a temperature that does not alter it, since sulphides oxidise and clays lose structural water if overheated, and grind or sieve as the method requires.
- M1: weigh the clean, dry pycnometer with its stopper.
- M2: add the dry sample (for example about 20 g in a 50 mL flask) and weigh again.
- Add enough water to cover the sample and remove trapped air, by vacuum or by gentle boiling followed by cooling, until no more bubbles appear. This is the critical step, because an air bubble is counted as solid volume and makes the SG too low.
- M3: fill with de-aired water at a recorded temperature, insert the stopper so that the excess spills from the capillary, dry the outside and weigh.
- M4: empty, clean and fill with water only at the same temperature, and weigh.
- Repeat with a second sample. If the two results do not agree closely, establish the cause and repeat.
Calculation
where
- empty, dry pycnometer with stopper (g)
- pycnometer plus dry sample (g)
- pycnometer plus sample, filled with water (g)
- pycnometer filled with water only (g)
(M4 − M1) is the mass of water that fills the flask, and (M3 − M2) is the mass of water that fills it around the sample. The difference is the mass of water displaced by the sample, which equals its volume in millilitres when the water density is 1 g/mL.
Worked example: M1 = 32.105 g, M2 = 52.105 g, M3 = 93.010 g, M4 = 80.385 g.
SG = (52.105 − 32.105) ÷ [(80.385 − 32.105) − (93.010 − 52.105)] = 20.000 ÷ (48.280 − 40.905) = 20.000 ÷ 7.375 = 2.71.
The result is relative to water at the test temperature. To report a density in g/cm³, it is multiplied by the density of water at that temperature (for example 0.997 g/cm³ at 25 °C), as test standards describe.
Sources of error
Trapped air makes the SG too low. Thorough de-airing is essential; fine and hydrophobic powders, such as graphite and some sulphides, retain air persistently, and a drop of wetting agent can help. Temperature changes between the M3 and M4 weighings alter both water density and flask volume, and water on the outside of the flask or in the stopper capillary introduces further error.
Soluble minerals, including some salts, dissolve in water; a non-reacting liquid of known density or a gas pycnometer should be used for them. With small samples, the small mass and volume differences magnify weighing errors, so an adequate sample mass and a balance reading to 0.001 g are required.
Gas (helium) pycnometers measure volume by gas displacement. They are fast, avoid wetting problems and suit fine powders, and many laboratories now use them for routine work.
Solids SG from pulp density
If the SG of a pulp (from a density gauge or by weighing a known volume) and its percent solids (by drying a weighed sample) are known, the solids SG follows:
where
- ,
- specific gravity of the solids and of the pulp
- solids content by mass (fraction), measured by drying a weighed pulp sample
Example: a leach feed pulp of SG 1.395 at 45% solids gives SGs = 0.45 ÷ (1 ÷ 1.395 − 1 + 0.45) = 0.45 ÷ 0.167 = 2.70. The calculation is sensitive to small errors in pulp SG, so it serves as a check rather than a replacement for a pycnometer measurement.
Specific gravity and bulk density
SG describes the solid material. Bulk density describes a mass of broken ore including the voids between particles, and is much lower: crushed ore of SG 2.7 might have a bulk density of about 1.6 to 1.8 t/m³ depending on size distribution and moisture. Bulk density applies to bins, stockpiles and conveyors; SG applies to slurries and inventories.
Glossary
- Specific gravity
- Density of a material divided by the density of water.
- Pycnometer
- A flask of fixed, precisely known volume used to measure the volume of a powder.
- De-airing
- Removing air trapped among particles, by vacuum or boiling, before the final weighing.
- Bulk density
- Mass per volume of broken material, including the voids between particles.
- Pulp
- A mixture of ore particles and water; also called slurry.
- % solids
- Mass of dry solids as a percentage of the mass of pulp.
- Gas pycnometer
- An instrument that measures solid volume by helium displacement.
Frequently asked questions
How is specific gravity calculated from pycnometer readings?
SG = (M2 − M1) ÷ [(M4 − M1) − (M3 − M2)], where M1 is the empty flask, M2 the flask plus sample, M3 the flask plus sample and water, and M4 the flask plus water.
Why is the pycnometer SG too low?
Air trapped among the particles is the most common cause. De-airing should be extended by vacuum or gentle boiling, and the water must be at the same temperature for both water weighings.
Is specific gravity the same as density?
Numerically almost the same in g/cm³ or t/m³, because the density of water is close to 1. Strictly, SG is a ratio and has no units.
What SG should be used for gold ore?
It should be measured. Most gold ores are 2.6 to 2.9, but sulphide-rich ores can be higher. The small amount of gold itself does not noticeably change the ore SG.
Discuss your plant with a metallurgist
Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.
Talk to a metallurgistReferences and further reading
- Standards Australia. AS 1289.3.5.1, Methods of testing soils for engineering purposes: determination of the soil particle density of a soil, standard method.
- ASTM D854. Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer. ASTM International.
- Deer, W.A., Howie, R.A. and Zussman, J. (2013). An Introduction to the Rock-Forming Minerals, 3rd edition. Mineralogical Society.
Worked examples and charts marked illustrative use invented figures, not data from any operation.