A
- AARL
Anglo American Research Laboratories elution: acid wash, caustic cyanide pre-soak, hot water elution.
Explained in: Carbon elution: AARL vs Zadra, with calculations
- Abrasion index, Ai
Bond's laboratory measure of how abrasive an ore is to steel.
Explained in: Grinding ball size and ball wear rate calculation
- Acid plant
A plant that converts sulphur dioxide into sulphuric acid.
Explained in: Roasting refractory gold: two-stage roasting and SO2
- Acid roast
Baking beta spodumene with concentrated sulphuric acid to form lithium sulphate.
Explained in: Lithium hydroxide from spodumene: process and LCE
- Acid wash
Dilute hydrochloric acid treatment that removes scale from carbon.
Explained in: Carbon elution: AARL vs Zadra, with calculations, Carbon regeneration kilns and carbon activity
- Activated carbon
Porous carbon granules that adsorb dissolved gold from solution.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses, Carbon activity, gold adsorption isotherm and k-n kinetics, Carbon regeneration kilns and carbon activity
- Activator
A reagent that changes a mineral's surface so the collector can attach.
Explained in: Flotation reagents, froth and gas dispersion explained
- Active content
The fraction of a reagent product that is the active chemical.
Explained in: Reagent dosing calculation: g/t to pump flow
- Activity ratio
Adsorption rate of regenerated carbon divided by that of new carbon, from the same test.
Explained in: Carbon regeneration kilns and carbon activity
- Adsorption
Molecules sticking to a surface; here, gold cyanide sticking to the pores of carbon.
Explained in: Carbon activity, gold adsorption isotherm and k-n kinetics
- Agglomeration
Binding fines to coarse particles with cement or acid and water so the heap stays permeable.
Explained in: Heap leach column test: procedure and scale-up
- Air allowance
The fraction of the cell volume taken up by air bubbles and internals, which slurry cannot use.
Explained in: Flotation cell sizing calculation with worked example
- Aliquot
The small portion of a pulverised sample weighed out for assay.
Explained in: Gy's formula: minimum sample mass calculation explained
- Alpha and beta spodumene
The natural, dense form and the heat-converted, more reactive form.
Explained in: Lithium hydroxide from spodumene: process and LCE
- AMIRA P754
An industry code of practice for metal accounting.
Explained in: Month-end metal accounting: check-in vs check-out
- Ampere-hour
One ampere flowing for one hour: 3,600 coulombs.
Explained in: Electrowinning current efficiency and Faraday's law
- Angle of repose
The natural slope of a pile of loose ore.
Explained in: Crushing circuit design: rates, screens and stockpiles
- Anode
The positive electrode, where water is split into oxygen and acid in most electrowinning cells.
Explained in: Electrowinning current efficiency and Faraday's law
- Aperture
The size of the openings in the screen panel.
Explained in: Screen efficiency calculation with worked example
- Apex and vortex finder
The bottom outlet and the top outlet tube of the cyclone. Their sizes set the split of water and solids.
Explained in: Hydrocyclone partition curve and d50 cut size explained
- Application rate
Solution applied per hour per square metre of heap surface (L/h·m²).
Explained in: Heap leach column test: procedure and scale-up
- Arsenic trioxide
As₂O₃, the volatile arsenic compound driven off in the first roasting stage and collected from the gas.
Explained in: Roasting refractory gold: two-stage roasting and SO2
- Assay
The measured grade of a sample, such as % copper or grams of gold per tonne.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Attrition
Wear and breakage of carbon granules into fines.
Explained in: Agitator design for leach tanks: power, suspension
- Autoclave
A sealed pressure vessel for reactions above the normal boiling point.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Availability
The share of calendar time the plant was able to run.
Explained in: Plant availability, utilisation and OEE explained
B
- Baffles
Vertical strips on the tank wall that stop the slurry swirling as a whole.
Explained in: Agitator design for leach tanks: power, suspension
- Ball filling
The fraction of the mill volume occupied by the ball bed, voids included.
Explained in: Grinding ball size and ball wear rate calculation
- Ball mill
A rotating drum partly filled with steel balls that grind ore to a fine powder.
Explained in: Bond work index test: how to run it and calculate Wi
- Bank
A row of flotation cells connected in series, so slurry flows from one to the next.
Explained in: Flotation cell sizing calculation with worked example
- Barren solution
Solution after the gold has been removed, returned to the leach.
Explained in: Merrill-Crowe process: zinc precipitation of gold
- Basic iron sulphate
An iron sulphate compound that can form in the autoclave and consume lime and cyanide later.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Battery grade
A product specification with tight limits on impurities for battery cathode manufacture.
Explained in: Lithium hydroxide from spodumene: process and LCE
- Bed
The layer of settled, compacting solids in the lower part of the thickener.
Explained in: Thickener operation: bed, flocculant and rise rate
- Bed pressure
The pressure measured at the base, used to infer bed mass.
Explained in: Thickener operation: bed, flocculant and rise rate
- Bed volume
The volume occupied by the carbon bed; flows and volumes are expressed as multiples of it.
Explained in: Carbon elution: AARL vs Zadra, with calculations
- Bias
A systematic error that always pushes a measurement the same way, such as a scale that always reads high.
Explained in: Mass balance reconciliation explained: WLS and chi-square, Assay QAQC: standards, blanks and duplicates explained, Month-end metal accounting: check-in vs check-out
- Bio-oxidation (BIOX)
Oxidation of sulphides by bacteria in aerated tanks.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Blank
Barren material used to detect contamination.
Explained in: Assay QAQC: standards, blanks and duplicates explained
- Blanking agent
A chemical that coats natural carbon to reduce preg-robbing.
Explained in: Diagnostic leach and preg-robbing test for gold ores
- Bleed
The share of a stream split off for treatment, here the share of cyclone underflow sent to gravity.
Explained in: Gravity circuit design for gold: bleed and recovery
- Blend grade
The tonnage-weighted average grade of the sources in a blend.
Explained in: Ore blending for the mill: grade and throughput
- Blinding
Openings coated or blocked by fine sticky material.
Explained in: Screen efficiency calculation with worked example, Filter leaf test: filtration rate and filter sizing
- Bond work index
A measure of how hard an ore is to grind, in kWh per tonne.
Explained in: Rapid Bond work index estimate for grinding circuit audits
- Breakage rate
How fast material coarser than a given size disappears during grinding, per minute.
Explained in: Rapid Bond work index estimate for grinding circuit audits
- Bubble surface area flux (Sb)
Bubble surface rising through each square metre of cell per second; 6Jg divided by the Sauter mean bubble diameter.
Explained in: Flotation reagents, froth and gas dispersion explained
- Bulk density
Mass of the ball bed divided by the volume it occupies, voids included.
Explained in: Grinding ball size and ball wear rate calculation, Ore specific gravity by pycnometer: method and formula
C
- Cake moisture
Water as a percentage of the wet cake mass.
Explained in: Filter leaf test: filtration rate and filter sizing
- Calcination
Heating a solid to change its structure or drive off components.
Explained in: Lithium hydroxide from spodumene: process and LCE
- Calcine
The solid product of roasting.
Explained in: Roasting refractory gold: two-stage roasting and SO2
- Calcining
Heating in air to drive off water and oxidise base metals and organics before smelting.
Explained in: Gold room operations: smelting and doré accounting
- Calculated head
The feed grade worked out by adding up the metal in all products, rather than assaying the feed directly.
Explained in: Flotation kinetics test and rate constant calculation, Bottle roll leach test procedure and calculations, Month-end metal accounting: check-in vs check-out
- Calibration column
A graduated tube on a pump's suction used to measure its actual flow.
Explained in: Reagent dosing calculation: g/t to pump flow
- Carbon activity
How fast carbon loads gold, compared with fresh carbon in a standard test.
Explained in: Carbon activity, gold adsorption isotherm and k-n kinetics
- Carbon fines
Small carbon particles broken from granules; they carry gold and are lost from the circuit if not captured.
Explained in: Carbon regeneration kilns and carbon activity
- Carbon inventory
The mass of carbon held in the adsorption circuit.
Explained in: Carbon regeneration kilns and carbon activity
- Carbon loading
The amount of gold held on carbon, in grams per tonne of carbon.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses
- Carbon movement
The rate at which carbon is advanced through the circuit and removed for elution (t/d).
Explained in: CIL circuit model: tanks in series and carbon loading
- Carbon profile
A survey of gold on carbon and gold in solution in every adsorption tank.
Explained in: Carbon activity, gold adsorption isotherm and k-n kinetics
- Caro's acid
Peroxymonosulphuric acid, H2SO5, a strong oxidant made from sulphuric acid and hydrogen peroxide.
Explained in: Cyanide destruction: SO2/air reagent calculation
- Carrying capacity
The most concentrate a froth can carry over the lip per unit of column area per minute.
Explained in: Flotation cell sizing calculation with worked example
- Cascade control
An outer loop that sets the setpoint of an inner, faster loop.
Explained in: Process control basics: PID loops and lambda tuning
- Catalyst
A substance that speeds a reaction without being consumed; copper in the SO2/air process.
Explained in: Cyanide destruction: SO2/air reagent calculation
- Cathode
The negative electrode, where metal ions gain electrons and plate out as metal.
Explained in: Electrowinning current efficiency and Faraday's law, Copper heap leach and SX-EW: the key calculations
- Cause and effect matrix
The table of what each trip or alarm does in the control system; used to test interlocks.
Explained in: Process plant commissioning: phases, tools and checklists
- Causticisation
Reacting a salt with sodium hydroxide; here, converting lithium sulphate to lithium hydroxide.
Explained in: Lithium hydroxide from spodumene: process and LCE
- Centrifugal concentrator
A spinning bowl that uses many times the force of gravity to trap dense particles such as gold.
Explained in: GRG test results explained: gravity gold circuit design, Gravity concentration criterion and calculations, Gravity circuit design for gold: bleed and recovery
- Certified reference material
A sample with a certified grade and uncertainty, used to check accuracy.
Explained in: Assay QAQC: standards, blanks and duplicates explained
- Channelling
Solution flowing down preferred paths and bypassing parts of the ore.
Explained in: Heap leach column test: procedure and scale-up
- Charge filling
The fraction of the mill volume occupied by the balls and the ore and water among them.
Explained in: Ball mill sizing: Bond energy and Rowland factors
- Check-in
Metal entering the plant, measured from feed tonnes and assays.
Explained in: Month-end metal accounting: check-in vs check-out
- Check-out
Metal leaving the plant in products and tailings.
Explained in: Month-end metal accounting: check-in vs check-out
- Chi-square test
A statistical check of whether the total adjustment is consistent with the stated measurement uncertainties.
Explained in: Mass balance reconciliation explained: WLS and chi-square
- Choke feeding
Keeping a cone crusher's chamber full of rock for consistent crushing.
Explained in: Bond crushing work index and crusher energy
- CIL
Carbon in leach: leaching and adsorption onto carbon happen in the same tanks.
Explained in: CIL circuit model: tanks in series and carbon loading
- CIL (carbon-in-leach)
Leaching and adsorbing in the same tanks, with carbon present while gold dissolves.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses
- CIP (carbon-in-pulp)
Leaching first in separate tanks, then adsorbing gold onto carbon in a second set of tanks.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses
- Circulating load
Material that a grinding mill sends back to itself through a classifier before it is fine enough to leave.
Explained in: GRG test results explained: gravity gold circuit design, Bond work index test: how to run it and calculate Wi, Gravity concentration criterion and calculations, Crushing circuit design: rates, screens and stockpiles, Gravity circuit design for gold: bleed and recovery
- Clarification
Filtering out suspended solids so the solution is clear.
Explained in: Merrill-Crowe process: zinc precipitation of gold
- Closed circuit
A mill with a classifier, usually cyclones, that returns coarse particles for more grinding.
Explained in: Ball mill sizing: Bond energy and Rowland factors, Crushing circuit design: rates, screens and stockpiles
- Closed-side setting
The smallest gap between the crushing surfaces, which controls product size.
Explained in: Bond crushing work index and crusher energy
- Closed-side setting (CSS)
The smallest gap between the crushing surfaces of a cone or jaw crusher; it largely sets the product size.
Explained in: Crushing circuit design: rates, screens and stockpiles
- Collector
A chemical that makes a mineral's surface water-repellent; fatty acids for spodumene.
Explained in: Spodumene concentrate production: DMS and flotation to SC6, Flotation kinetics test and rate constant calculation, Flotation reagents, froth and gas dispersion explained
- Column cell
A tall flotation cell with a deep froth washed by water, mostly used for cleaning.
Explained in: Flotation cell sizing calculation with worked example
- Column test
A laboratory or pilot test that leaches ore in a tall column to imitate a heap.
Explained in: Heap leach column test: procedure and scale-up
- Compression point
Where the settling curve turns from free settling into slow compaction of the bed.
Explained in: Thickener sizing: settling test and unit area calculation
- Concentrate
The valuable product stream, rich in the metal being recovered.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Concentration criterion
(Heavy mineral density − fluid density) ÷ (light mineral density − fluid density).
Explained in: Gravity concentration criterion and calculations
- Conditioner
An agitated tank that gives reagents time to act before flotation.
Explained in: Flotation cell sizing calculation with worked example
- Cone crusher
A crusher that breaks rock between a gyrating cone and a fixed bowl; usually secondary or tertiary.
Explained in: Bond crushing work index and crusher energy
- Confirmation bias
The tendency to notice evidence that supports an existing belief and to overlook evidence against it.
Explained in: Root cause analysis for metallurgical plant problems
- Counter-current decantation
A series of thickeners that washes leached solids with solution flowing the opposite way.
Explained in: Merrill-Crowe process: zinc precipitation of gold
- Counter-current decantation (CCD)
A series of thickeners in which solids and wash water flow in opposite directions.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Critical path
The longest chain of linked activities in a schedule; delays on it delay the end date.
Explained in: Process plant commissioning: phases, tools and checklists
- Critical speed
The speed at which the outer balls would stick to the shell; mills run at about 65 to 80% of it.
Explained in: Ball mill sizing: Bond energy and Rowland factors
- Cross-stream cutter
A sampler that moves through the whole falling stream at constant speed to take an increment.
Explained in: Sampling system design: cross-stream cutters explained
- Crud
A stable emulsion of solids, organic and aqueous that forms at the interface.
Explained in: Solvent extraction McCabe-Thiele diagram explained
- Crushing work index
Bond's measure of the energy rock takes to break by impact (kWh/t).
Explained in: Bond crushing work index and crusher energy
- Cumulative % passing
The share of a sample finer than a given sieve size.
Explained in: Particle size analysis and how to calculate P80
- Current efficiency
The fraction of the current that plates the wanted metal.
Explained in: Electrowinning current efficiency and Faraday's law, Copper heap leach and SX-EW: the key calculations
- CUSUM
Cumulative sum: the running total of each result's difference from a target.
Explained in: CUSUM chart for plant recovery: method and worked example
- Cut density
The density at which particles are split into floats and sinks.
Explained in: Heavy liquid separation test for spodumene ore, Spodumene DMS plant design: medium, cut density, Ep
- Cut-off time
The single date and time at which every measurement for a reporting period is taken.
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- Cut size, d50c
The particle size with a 50% chance of going to the underflow on the corrected curve.
Explained in: Hydrocyclone partition curve and d50 cut size explained
- Cyanate
OCN⁻, the much less toxic product of cyanide oxidation.
Explained in: Cyanide destruction: SO2/air reagent calculation, Free, WAD and total cyanide explained
- Cyanidation
Dissolving gold in a dilute cyanide solution in the presence of oxygen.
Explained in: Bottle roll leach test procedure and calculations
- Cyanide leaching
Dissolving gold from ore in a dilute cyanide solution with oxygen.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses
- Cyclone underflow
The coarse, dense stream from a hydrocyclone, which returns to the mill. Gravity gold collects here.
Explained in: GRG test results explained: gravity gold circuit design
D
- Davis tube
A laboratory magnetic separator used to measure the magnetic fraction of a ground sample.
Explained in: Magnetic separation and the Davis tube test
- Dead time
The delay between an output change and the first movement of the PV.
Explained in: Process control basics: PID loops and lambda tuning
- Deaeration
Removing dissolved oxygen under vacuum.
Explained in: Merrill-Crowe process: zinc precipitation of gold
- De-airing
Removing air trapped among particles, by vacuum or boiling, before the final weighing.
Explained in: Ore specific gravity by pycnometer: method and formula
- Decant return
Water pumped back from the pond on top of the tailings to the plant.
Explained in: Plant water balance: tailings, decant and make-up water
- Decision interval, h
The threshold the tabular CUSUM must cross to signal an alarm.
Explained in: CUSUM chart for plant recovery: method and worked example
- Delimitation error
Bias from a cut whose shape does not give every part of the stream an equal chance of selection.
Explained in: Sampling system design: cross-stream cutters explained
- Dense media separation
The plant process using a heavy suspension, usually ferrosilicon in water, in cyclones or drums.
Explained in: Heavy liquid separation test for spodumene ore
- Dense media separation (DMS)
Separating particles by density in a heavy liquid suspension, used on coarse spodumene.
Explained in: Spodumene concentrate production: DMS and flotation to SC6, Spodumene DMS plant design: medium, cut density, Ep
- Deportment
How the gold is distributed between minerals or forms in an ore.
Explained in: Diagnostic leach and preg-robbing test for gold ores
- Depressant
A reagent that stops a mineral from floating.
Explained in: Flotation reagents, froth and gas dispersion explained
- Desliming
Removing the finest particles before flotation.
Explained in: Spodumene concentrate production: DMS and flotation to SC6
- Detox
Short for cyanide destruction: oxidising cyanide in tailings before disposal.
Explained in: Cyanide destruction: SO2/air reagent calculation
- Diagnostic leach
A sequence of laboratory leaches that shows how much gold is free, locked in sulphides or locked in other minerals.
Explained in: Root cause analysis for metallurgical plant problems, Bottle roll leach test procedure and calculations, Diagnostic leach and preg-robbing test for gold ores
- Dilution
Mass of liquid per mass of solids in a pulp; a 25% solids pulp has a dilution of 3.
Explained in: Thickener sizing: settling test and unit area calculation
- Dissolved oxygen
Oxygen gas dissolved in the solution, measured in mg/L.
Explained in: Oxygen uptake rate test for gold leach slurries
- Dissolved oxygen (DO)
Oxygen gas dissolved in the slurry water, measured in mg/L.
Explained in: Dissolved oxygen in cyanide leaching: control and targets
- Doré
An impure bar of gold and silver produced at the mine for refining.
Explained in: Gold room operations: smelting and doré accounting
- Dosing pump
A metering pump that delivers a set flow of reagent solution.
Explained in: Reagent dosing calculation: g/t to pump flow
- Drain and rinse screen
A screen that drains medium from a product and then rinses off the remainder for recovery.
Explained in: Spodumene DMS plant design: medium, cut density, Ep
- Dry time
The part of the cycle when air is drawn through the cake to remove moisture.
Explained in: Filter leaf test: filtration rate and filter sizing
- DTR
Davis tube recovery: the magnetic fraction's mass as a percentage of the feed.
Explained in: Magnetic separation and the Davis tube test
- Duplicate
A second split of a sample assayed to measure precision.
Explained in: Assay QAQC: standards, blanks and duplicates explained
- Durand factor, F_L
An empirical factor in Durand's equation that depends on particle size and solids concentration.
Explained in: Slurry pipeline critical velocity: Durand equation
E
- Ecart probable, Ep
A measure of DMS sharpness: half the density range between 25% and 75% reporting to sinks.
Explained in: Heavy liquid separation test for spodumene ore
- Efficiency factor
A multiplier that corrects Bond's energy for conditions different from his reference mill.
Explained in: Ball mill sizing: Bond energy and Rowland factors
- Efficiency factors
Rowland's corrections to Bond's equation for conditions that differ from the reference case.
Explained in: Bond work index test: how to run it and calculate Wi
- Electrolyte
The strong copper and acid solution from which copper is electrowon.
Explained in: Copper heap leach and SX-EW: the key calculations
- Electrowinning
Plating gold out of solution onto cathodes using an electric current.
Explained in: Gold reconciliation: F-factors, GIC and scheduling, Electrowinning current efficiency and Faraday's law
- Electrowinning (EW)
Plating metal from solution onto cathodes by passing an electric current.
Explained in: Copper heap leach and SX-EW: the key calculations
- Eluant
The solution pumped through the carbon to strip it.
Explained in: Carbon elution: AARL vs Zadra, with calculations
- Eluate
The gold-rich solution produced by stripping gold off loaded carbon.
Explained in: Electrowinning current efficiency and Faraday's law, Carbon elution: AARL vs Zadra, with calculations
- Elution
Stripping gold off loaded carbon with hot caustic cyanide solution.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses, Gold reconciliation: F-factors, GIC and scheduling, Carbon activity, gold adsorption isotherm and k-n kinetics, Carbon elution: AARL vs Zadra, with calculations
- End point
The colour change that shows all the cyanide (or alkali) has reacted.
Explained in: Free cyanide titration with silver nitrate: method and maths
- Entrainment
Fine particles carried into the froth with water rather than attached to bubbles.
Explained in: Flotation kinetics test and rate constant calculation, Flotation reagents, froth and gas dispersion explained
- Ep (écart probable)
Half the density difference between the 75% and 25% points of the partition curve; a measure of separation sharpness.
Explained in: Spodumene DMS plant design: medium, cut density, Ep
- Excess air
Air supplied beyond the stoichiometric need, to complete the reactions.
Explained in: Roasting refractory gold: two-stage roasting and SO2
- Extractant
The chemical in the organic phase that binds the metal.
Explained in: Solvent extraction McCabe-Thiele diagram explained
- Extraction
The fraction of gold in the ore that dissolved in the test.
Explained in: Bottle roll leach test procedure and calculations
- Extraction error
Bias from particles that should be in the cut bouncing off, or ones outside it falling in.
Explained in: Sampling system design: cross-stream cutters explained
F
- F1, F2, F3
Ratios comparing grade control with the resource model (F1), the mill with grade control (F2), and the mill with the resource model (F3).
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- F80, P80
Sizes that 80% of the feed and product pass through, in µm.
Explained in: Bond work index test: how to run it and calculate Wi, Ball mill sizing: Bond energy and Rowland factors
- False alarm
An alarm when nothing has actually changed.
Explained in: CUSUM chart for plant recovery: method and worked example
- Faraday constant
The electric charge carried by one mole of electrons: 96,485 coulombs.
Explained in: Electrowinning current efficiency and Faraday's law
- Feed
The ore entering the plant or a part of it.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Feedwell
The central chamber where feed enters a thickener, is diluted and mixed with flocculant.
Explained in: Thickener sizing: settling test and unit area calculation, Thickener operation: bed, flocculant and rise rate
- Ferrosilicon (FeSi)
An iron-silicon alloy powder, about 6.8 t/m³ and magnetic, used to make dense medium.
Explained in: Spodumene DMS plant design: medium, cut density, Ep
- Field gradient
How quickly the magnetic field strength changes with distance; it creates the pulling force.
Explained in: Magnetic separation and the Davis tube test
- Filter cake
The layer of solids left on the cloth.
Explained in: Filter leaf test: filtration rate and filter sizing
- Filtrate
The liquid that passes through the cake and cloth.
Explained in: Filter leaf test: filtration rate and filter sizing
- Fineness
Gold content in parts per thousand by mass.
Explained in: Gold room operations: smelting and doré accounting
- First-order kinetics
A process in which the rate of change is proportional to the amount remaining, giving an exponential decay.
Explained in: Rapid Bond work index estimate for grinding circuit audits, CIL circuit model: tanks in series and carbon loading
- Fishbone (Ishikawa) diagram
A diagram grouping possible causes of a problem into families such as ore, equipment, process and measurement.
Explained in: Root cause analysis for metallurgical plant problems
- Five whys
Asking 'why' repeatedly until the answer is something that can be acted on.
Explained in: Root cause analysis for metallurgical plant problems
- Float
How long an activity can slip without delaying the end date.
Explained in: Process plant commissioning: phases, tools and checklists
- Flocculant
A long-chain polymer that binds fine particles into larger flocs, which settle much faster.
Explained in: Thickener sizing: settling test and unit area calculation, Reagent dosing calculation: g/t to pump flow, Thickener operation: bed, flocculant and rise rate
- Flocculation
Binding fine particles into larger flocs that settle faster.
Explained in: Stokes' law and settling velocity for metallurgists
- Flotation
Separating particles by making the valuable mineral water-repellent so it attaches to air bubbles and rises.
Explained in: Spodumene concentrate production: DMS and flotation to SC6
- Flux
Chemicals added to the furnace charge to dissolve impurities into a fluid slag.
Explained in: Gold room operations: smelting and doré accounting
- Form time
The part of the cycle when the cake is built up under vacuum in the slurry.
Explained in: Filter leaf test: filtration rate and filter sizing
- Fouling
Build-up of scale or organic matter that blocks carbon pores.
Explained in: Carbon regeneration kilns and carbon activity
- Free cyanide
Cyanide in solution that is available to dissolve gold.
Explained in: Dissolved oxygen in cyanide leaching: control and targets, Bottle roll leach test procedure and calculations, Free cyanide titration with silver nitrate: method and maths, Free, WAD and total cyanide explained
- Free gold
Gold particles not locked in other minerals.
Explained in: Gravity circuit design for gold: bleed and recovery
- Free-milling gold
Gold that dissolves directly in cyanide after normal grinding.
Explained in: Diagnostic leach and preg-robbing test for gold ores
- Free settling
The early stage of a settling test, when the interface falls at a constant rate.
Explained in: Thickener sizing: settling test and unit area calculation
- Freundlich equation
An empirical isotherm, q = K·C^(1/n), which is a straight line on log-log axes.
Explained in: Carbon activity, gold adsorption isotherm and k-n kinetics
- Frother
A chemical that makes small, stable bubbles and a froth that holds the floated mineral.
Explained in: Flotation kinetics test and rate constant calculation, Flotation reagents, froth and gas dispersion explained
- Froth recovery
The fraction of particles entering the froth attached to bubbles that reach the concentrate.
Explained in: Flotation reagents, froth and gas dispersion explained
- Fundamental sampling error
The random error caused by the particle-to-particle variation in grade, present even when sampling is done correctly.
Explained in: Gy's formula: minimum sample mass calculation explained
G
- Gangue
The worthless minerals in the ore.
Explained in: Spodumene concentrate production: DMS and flotation to SC6
- Gas pycnometer
An instrument that measures solid volume by helium displacement.
Explained in: Ore specific gravity by pycnometer: method and formula
- Gates–Gaudin–Schuhmann distribution
An equation that plots as a straight line on log-log axes, with a size modulus and a slope.
Explained in: Particle size analysis and how to calculate P80
- Gold in circuit
Gold held in the plant at a point in time, in solution, on carbon and in other inventories.
Explained in: Month-end metal accounting: check-in vs check-out
- Gold in circuit (GIC)
Gold recovered from the ore but not yet poured into bars, held in solution, on carbon, in elution, electrowinning and the gold room.
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- Gold room balance
A reconciliation of gold into and out of the gold room for each pour.
Explained in: Gold room operations: smelting and doré accounting
- Grade
How much metal is in the material, for example 1.2% Cu or 2.0 g/t Au.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Grade control model
The short-term estimate made from close-spaced drilling just before mining, used to decide what is ore and what is waste.
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- Grate-discharge mill
A mill with a grate at the discharge end; K = 330 when wet.
Explained in: Grinding ball size and ball wear rate calculation
- Gravity concentration
Separating minerals by density using water, motion and gravity or centrifugal force.
Explained in: Gravity concentration criterion and calculations
- Gravity-recoverable gold (GRG)
The share of the gold in an ore that a laboratory gravity concentrator can recover under the standard test.
Explained in: GRG test results explained: gravity gold circuit design
- GRG
Gravity-recoverable gold: the share of gold a laboratory gravity test can recover.
Explained in: Gravity circuit design for gold: bleed and recovery
- Grindability
How easily a material breaks in a grinding mill.
Explained in: Rapid Bond work index estimate for grinding circuit audits
- Grindability (Gbp)
Net grams of fine material produced per mill revolution at steady state in the Bond test.
Explained in: Bond work index test: how to run it and calculate Wi
- Grinding media
The steel balls (or rods) that grind ore in a mill.
Explained in: Grinding ball size and ball wear rate calculation
- g/t
Grams of reagent per tonne of dry ore; the same as parts per million by mass.
Explained in: Reagent dosing calculation: g/t to pump flow
H
- HARD
Half absolute relative difference between a sample and its duplicate.
Explained in: Assay QAQC: standards, blanks and duplicates explained
- Head
The height to which a pump can lift a fluid; also used for friction losses expressed as height.
Explained in: Slurry pipeline critical velocity: Durand equation
- Head grade
The grade of the plant feed.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Head ratio
The ratio of the head a pump develops on slurry to its head on water at the same flow and speed.
Explained in: Slurry pipeline critical velocity: Durand equation
- Heap leach
Leaching crushed or run-of-mine ore stacked on a lined pad by irrigating it with solution.
Explained in: Copper heap leach and SX-EW: the key calculations
- Heap leaching
Leaching crushed ore stacked on a lined pad by trickling solution through it.
Explained in: Heap leach column test: procedure and scale-up
- Heavy liquid separation
A laboratory float-sink test that splits ore into density fractions using liquids of known density.
Explained in: Heavy liquid separation test for spodumene ore
- Hematite
Fe₂O₃, a weakly magnetic iron oxide.
Explained in: Magnetic separation and the Davis tube test
- Heterogeneity test
An experiment that assays many equal-mass samples of the same material to measure its sampling constant directly.
Explained in: Gy's formula: minimum sample mass calculation explained
- Hindered settling
Slower settling caused by neighbouring particles in a concentrated slurry.
Explained in: Stokes' law and settling velocity for metallurgists
- Hydrofoil
An impeller with shaped blades that pumps slurry efficiently with a low power number.
Explained in: Agitator design for leach tanks: power, suspension
- Hypothesis
A possible explanation that can be tested and could turn out to be wrong.
Explained in: Root cause analysis for metallurgical plant problems
I
- Impact strength
Energy at breakage divided by specimen thickness (J/mm).
Explained in: Bond crushing work index and crusher energy
- Impeller
The rotating blades on an agitator shaft that move the slurry.
Explained in: Agitator design for leach tanks: power, suspension
- Increment
One cut taken by a sampler from a stream.
Explained in: Sampling system design: cross-stream cutters explained
- Intensive leaching
A high-strength cyanide leach used to dissolve gold from a small gravity concentrate.
Explained in: GRG test results explained: gravity gold circuit design
- Intensive leach reactor
A small, high-cyanide, high-oxygen reactor that dissolves gold from gravity concentrate quickly.
Explained in: Gravity circuit design for gold: bleed and recovery
- International Cyanide Management Code
A voluntary industry code for the safe manufacture, transport and use of cyanide in gold mining.
Explained in: Free, WAD and total cyanide explained
- Interstage screen
A screen that keeps carbon in its tank while slurry flows on.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses
- Is / is not analysis
A table comparing where a problem occurs with where it could occur but does not, from Kepner and Tregoe's method.
Explained in: Root cause analysis for metallurgical plant problems
- Isotherm
The relationship between gold in solution and gold on carbon at equilibrium, at constant temperature.
Explained in: Carbon activity, gold adsorption isotherm and k-n kinetics, Solvent extraction McCabe-Thiele diagram explained
J
- Jaw crusher
A crusher that breaks rock between a fixed and a moving jaw; usually the primary crusher.
Explained in: Bond crushing work index and crusher energy
- Just-suspended speed
The slowest speed at which no particle rests on the tank floor for more than a moment.
Explained in: Agitator design for leach tanks: power, suspension
L
- Lambda (λ)
The chosen closed-loop time constant in lambda tuning.
Explained in: Process control basics: PID loops and lambda tuning
- Laser diffraction
Sizing particles by how they scatter laser light; reports volume-based equivalent sphere sizes.
Explained in: Particle size analysis and how to calculate P80
- LCE
Lithium carbonate equivalent: the mass of Li₂CO₃ the contained lithium could make.
Explained in: Heavy liquid separation test for spodumene ore, Lithium hydroxide from spodumene: process and LCE
- Lead nitrate
A small addition that coats zinc with lead and speeds precipitation.
Explained in: Merrill-Crowe process: zinc precipitation of gold
- Leaf test
A bench test using a small filter leaf to copy one cycle of a vacuum filter.
Explained in: Filter leaf test: filtration rate and filter sizing
- Least-squares balancing
Adjusting all measurements, weighted by their precision, so every node balances.
Explained in: Flotation circuit survey and mass balance guide
- Lever rule
The rule that gives the mix of two components needed to reach a target value between them.
Explained in: Ore blending for the mill: grade and throughput
- Liberation
Freeing a valuable mineral from the rock around it by crushing and grinding.
Explained in: GRG test results explained: gravity gold circuit design
- Liberation size
The particle size below which the valuable mineral exists mostly as separate grains.
Explained in: Gy's formula: minimum sample mass calculation explained
- Lift
One layer of ore stacked on a heap.
Explained in: Heap leach column test: procedure and scale-up
- Limit deposit velocity
The velocity below which solids settle out and form a bed in a pipe.
Explained in: Slurry pipeline critical velocity: Durand equation
- LIMS
Low-intensity magnetic separator, normally a drum separator for magnetite.
Explained in: Magnetic separation and the Davis tube test
- Li₂O
Lithium oxide; lithium grades are quoted as % Li₂O.
Explained in: Spodumene concentrate production: DMS and flotation to SC6
- LiOH·H₂O
Lithium hydroxide monohydrate, the usual hydroxide product.
Explained in: Lithium hydroxide from spodumene: process and LCE
- Lip loading
Concentrate mass overflowing per metre of froth lip; a check on froth removal.
Explained in: Flotation cell sizing calculation with worked example
- Live capacity
The part of a stockpile or bin that flows out by gravity through the feeders.
Explained in: Crushing circuit design: rates, screens and stockpiles
- Loaded and stripped organic
Organic leaving extraction carrying metal, and organic leaving stripping with little metal.
Explained in: Solvent extraction McCabe-Thiele diagram explained
- Loaded carbon grade
Gold on carbon leaving the first tank (g/t of carbon).
Explained in: CIL circuit model: tanks in series and carbon loading
- Locked-cycle test
A repeated laboratory cycle that imitates a continuous closed grinding circuit.
Explained in: Bond work index test: how to run it and calculate Wi
- Lot
The whole body of material being sampled, such as a stockpile, a shift's plant feed or a drill hole interval.
Explained in: Gy's formula: minimum sample mass calculation explained, Sampling system design: cross-stream cutters explained
M
- Magnetic susceptibility
How strongly a material is magnetised in an applied field.
Explained in: Magnetic separation and the Davis tube test
- Magnetite
Fe₃O₄, a strongly magnetic iron oxide.
Explained in: Magnetic separation and the Davis tube test
- Make-up ball size
The size of the new balls added to replace wear; usually the largest ball in the mill.
Explained in: Grinding ball size and ball wear rate calculation
- Make-up water
Fresh or raw water added to the plant to replace water lost.
Explained in: Plant water balance: tailings, decant and make-up water
- Mass balance
An account showing that what enters a process equals what leaves it plus any change in what is held inside.
Explained in: Mass balance reconciliation explained: WLS and chi-square, Flotation circuit survey and mass balance guide
- Mass pull
The percentage of the feed mass that reports to concentrate.
Explained in: Gravity concentration criterion and calculations
- Mass split
Concentrate mass as a fraction of feed mass for a bank.
Explained in: Flotation circuit survey and mass balance guide
- Mass yield
The share of the feed's mass that reports to the concentrate.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Maximum recovery, R∞
The recovery the model predicts after a very long flotation time.
Explained in: Flotation kinetics test and rate constant calculation
- Mechanical completion
The point when a system is built and tested to construction requirements and ready for pre-commissioning.
Explained in: Process plant commissioning: phases, tools and checklists
- Medium
The ferrosilicon and water suspension in which particles separate.
Explained in: Spodumene DMS plant design: medium, cut density, Ep
- Metal accounting
Measuring and reporting the metal received, produced and held by a plant over a period.
Explained in: Month-end metal accounting: check-in vs check-out
- Metal-cyanide complex
A dissolved compound of a metal ion with several cyanide ions, such as copper or iron cyanide.
Explained in: Free, WAD and total cyanide explained
- Middlings
Particles of intermediate density, often part spodumene and part gangue.
Explained in: Spodumene DMS plant design: medium, cut density, Ep
- Mine call factor
Gold recovered plus gold in residue, as a percentage of the gold the mine's measurements say was sent to the plant.
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- Misplaced material
Fines in the oversize or coarse particles in the undersize.
Explained in: Screen efficiency calculation with worked example
- Mixer-settler
A box where the phases are mixed then allowed to separate.
Explained in: Solvent extraction McCabe-Thiele diagram explained
- Molarity
Concentration in moles per litre.
Explained in: Free cyanide titration with silver nitrate: method and maths
- MTBF
Mean time between failures.
Explained in: Plant availability, utilisation and OEE explained
- MTTR
Mean time to repair, including waiting for parts and people.
Explained in: Plant availability, utilisation and OEE explained
N
- Nameplate
The design throughput of the plant.
Explained in: Process plant commissioning: phases, tools and checklists
- Near-size particle
A particle only slightly smaller than the aperture, which passes with difficulty.
Explained in: Screen efficiency calculation with worked example
- Neutralisation
Raising the pH of acid solids or liquor with limestone or lime.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Newton's law
The settling velocity of a coarse particle in turbulent flow.
Explained in: Stokes' law and settling velocity for metallurgists
- Node
A point in a flowsheet where streams join or split, such as a bank of cells.
Explained in: Flotation circuit survey and mass balance guide
- Non-Newtonian slurry
A slurry, usually fine and concentrated, whose resistance to flow depends on the shear rate.
Explained in: Slurry pipeline critical velocity: Durand equation
O
- OEE
Overall equipment effectiveness: utilisation × performance × quality.
Explained in: Plant availability, utilisation and OEE explained
- Open area
The fraction of the screen surface that is opening rather than wire or panel.
Explained in: Screen efficiency calculation with worked example
- Operating baseline
The normal relationship between throughput and ore hardness, used to judge later changes.
Explained in: Rapid Bond work index estimate for grinding circuit audits
- Operating line
The mass balance line on a McCabe-Thiele diagram; its slope is the A/O flow ratio.
Explained in: Solvent extraction McCabe-Thiele diagram explained
- OP (output)
What the controller adjusts, such as valve position or pump speed.
Explained in: Process control basics: PID loops and lambda tuning
- Ore commissioning
Introducing ore and reagents and bringing the process on line; also called hot commissioning.
Explained in: Process plant commissioning: phases, tools and checklists
- Ore type
A domain of ore with similar grade, hardness and metallurgical behaviour.
Explained in: Ore blending for the mill: grade and throughput
- Overflow
The fine product leaving through the vortex finder at the top.
Explained in: Hydrocyclone partition curve and d50 cut size explained
- Overflow mill
A ball mill that discharges by slurry overflowing the discharge trunnion; K = 350 in the ball size equation.
Explained in: Grinding ball size and ball wear rate calculation
- Oversize
Material that travels over the screen and leaves at the discharge end.
Explained in: Screen efficiency calculation with worked example
- Oxidant
A substance that takes electrons from another, allowing gold to dissolve.
Explained in: Dissolved oxygen in cyanide leaching: control and targets
- Oxygen uptake rate
How fast a slurry consumes dissolved oxygen (mg/L per minute).
Explained in: Oxygen uptake rate test for gold leach slurries
P
- P80
The size that 80% of the material passes through, used as a single number for the fineness of a grind.
Explained in: GRG test results explained: gravity gold circuit design, Particle size analysis and how to calculate P80
- Pan evaporation
Evaporation measured from a standard open pan; converted to open water with a pan coefficient.
Explained in: Plant water balance: tailings, decant and make-up water
- Pareto chart
A bar chart of causes sorted from largest to smallest.
Explained in: Plant availability, utilisation and OEE explained
- Partition curve
A graph of the fraction of each particle size that reports to the underflow.
Explained in: Hydrocyclone partition curve and d50 cut size explained, Spodumene DMS plant design: medium, cut density, Ep
- Passivation
Forming a coating on a mineral surface that slows further reaction.
Explained in: Oxygen uptake rate test for gold leach slurries
- Pegging
Particles wedged in the openings.
Explained in: Screen efficiency calculation with worked example
- Pegmatite
A coarse-grained igneous rock that can host spodumene.
Explained in: Spodumene concentrate production: DMS and flotation to SC6
- Performance
Average rate while running divided by design rate.
Explained in: Plant availability, utilisation and OEE explained
- Performance test
A formal test that proves the plant meets its contract guarantees.
Explained in: Process plant commissioning: phases, tools and checklists
- Pinion power
The power delivered to the mill shell through the pinion and girth gear.
Explained in: Ball mill sizing: Bond energy and Rowland factors
- pKa
The pH at which an acid is half dissociated; about 9.2 for HCN.
Explained in: Free, WAD and total cyanide explained
- Plant trial
A test of a change on the operating plant, designed so that ore variation does not hide or fake the result.
Explained in: Root cause analysis for metallurgical plant problems
- PLS
Pregnant leach solution: the copper-bearing solution draining from the heap.
Explained in: Copper heap leach and SX-EW: the key calculations
- Plug flow
Flow where every element of slurry spends exactly the same time in the vessel.
Explained in: CIL circuit model: tanks in series and carbon loading
- Power number
A dimensionless number for an impeller that links power to speed, diameter and density in turbulent flow.
Explained in: Agitator design for leach tanks: power, suspension
- Pre-aeration
Aerating the slurry before cyanide is added, to satisfy oxygen-hungry minerals first.
Explained in: Dissolved oxygen in cyanide leaching: control and targets, Oxygen uptake rate test for gold leach slurries
- Precipitate
The solid gold, silver, zinc and other metals collected on the filter press.
Explained in: Merrill-Crowe process: zinc precipitation of gold
- Precision
How closely repeated measurements of the same sample agree.
Explained in: Assay QAQC: standards, blanks and duplicates explained
- Pre-commissioning
Checks and tests without process fluids: energising, loop checks, rotation, no-load runs, interlock tests.
Explained in: Process plant commissioning: phases, tools and checklists
- Pregnant solution
Cyanide solution carrying dissolved gold and silver.
Explained in: Merrill-Crowe process: zinc precipitation of gold, Heap leach column test: procedure and scale-up
- Preg-robbing
When natural carbon or clay in the ore adsorbs dissolved gold and takes it to tailings.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses, Bottle roll leach test procedure and calculations, Diagnostic leach and preg-robbing test for gold ores, Roasting refractory gold: two-stage roasting and SO2, Ore blending for the mill: grade and throughput
- Pressure oxidation (POX)
Oxidation of sulphides in an autoclave at high temperature and oxygen pressure.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Prill
A small droplet of metal trapped in slag.
Explained in: Gold room operations: smelting and doré accounting
- Primary crusher
The first crusher, usually a gyratory or jaw crusher, which takes run-of-mine ore.
Explained in: Crushing circuit design: rates, screens and stockpiles
- Process gain
Change in PV divided by the change in OP that caused it, in % of range.
Explained in: Process control basics: PID loops and lambda tuning
- Protective alkalinity
The excess lime that keeps pH high enough to stop cyanide turning into hydrogen cyanide gas.
Explained in: Bottle roll leach test procedure and calculations, Free cyanide titration with silver nitrate: method and maths
- Pulp
A mixture of ore particles and water; also called slurry.
Explained in: Ore specific gravity by pycnometer: method and formula
- Punch list
The list of defects and incomplete items, each with a category, owner and due date.
Explained in: Process plant commissioning: phases, tools and checklists
- PV (process variable)
The measured value the loop controls, such as density or level.
Explained in: Process control basics: PID loops and lambda tuning
- Pycnometer
A flask of fixed, precisely known volume used to measure the volume of a powder.
Explained in: Ore specific gravity by pycnometer: method and formula
- Pyrrhotite
An iron sulphide mineral that reacts readily and consumes oxygen and cyanide.
Explained in: Dissolved oxygen in cyanide leaching: control and targets, Oxygen uptake rate test for gold leach slurries
Q
- QAQC
Quality assurance and quality control: the procedures and checks that make assay data reliable.
Explained in: Assay QAQC: standards, blanks and duplicates explained
- Quench
Rapid cooling of hot carbon in water as it leaves the kiln.
Explained in: Carbon regeneration kilns and carbon activity
R
- RACI matrix
A table showing who is Responsible, Accountable, Consulted and Informed for each activity.
Explained in: Process plant commissioning: phases, tools and checklists
- Raffinate
The aqueous solution leaving extraction, depleted of metal.
Explained in: Solvent extraction McCabe-Thiele diagram explained, Copper heap leach and SX-EW: the key calculations
- Rake torque
The turning load on the rake drive; a key protection measurement.
Explained in: Thickener operation: bed, flocculant and rise rate
- Ramp-up
The period from first ore until the plant reaches its design throughput and recovery.
Explained in: Process plant commissioning: phases, tools and checklists
- Rate constant, k
How fast the floatable mineral comes off, in units of 1/min. A larger k means faster flotation.
Explained in: Flotation kinetics test and rate constant calculation
- Reconciliation
Adjusting measured values so the balance closes, in proportion to how uncertain each one is.
Explained in: Mass balance reconciliation explained: WLS and chi-square, Gold reconciliation: F-factors, GIC and scheduling, Ore blending for the mill: grade and throughput
- Recovery
The share of the metal in the feed that reports to the product.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Recovery per pass
The fraction of the gold in the stream treated that one pass through the concentrator captures.
Explained in: Gravity concentration criterion and calculations
- Reduction ratio
Feed size divided by product size, F80 ÷ P80.
Explained in: Ball mill sizing: Bond energy and Rowland factors, Bond crushing work index and crusher energy, Crushing circuit design: rates, screens and stockpiles
- Redundancy
Having more measurements than the minimum needed, so that they can check each other.
Explained in: Mass balance reconciliation explained: WLS and chi-square
- Reference ore
A well-tested ore with a known work index, used for comparison.
Explained in: Rapid Bond work index estimate for grinding circuit audits
- Reference value, k
The allowance subtracted each day so ordinary noise does not build up in a tabular CUSUM.
Explained in: CUSUM chart for plant recovery: method and worked example
- Refinery outturn
The refinery's final statement of the gold and silver it credits from each shipment of bars.
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- Refractory gold
Gold that does not leach well with cyanide after normal grinding, usually because it is locked in sulphides.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Refractory ore
Ore from which cyanide alone recovers gold poorly.
Explained in: Diagnostic leach and preg-robbing test for gold ores
- Regeneration
Heating eluted carbon in a kiln to burn off organic fouling and restore activity.
Explained in: Carbon activity, gold adsorption isotherm and k-n kinetics, Carbon elution: AARL vs Zadra, with calculations
- Regression to the mean
The tendency for an unusually bad or good result to be followed by a more normal one, whatever was done in between.
Explained in: Root cause analysis for metallurgical plant problems
- Relative standard deviation
The standard deviation divided by the mean, often given in per cent.
Explained in: Gy's formula: minimum sample mass calculation explained
- Residence time
The average time slurry spends in a cell or bank: volume divided by flow.
Explained in: Flotation cell sizing calculation with worked example
- Residue
The leached solids leaving a leach plant.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods, Bottle roll leach test procedure and calculations
- Resource model
The long-term estimate of tonnes and grade in the ground, built from exploration drilling.
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- Reynolds number
A ratio showing whether flow around a particle is smooth or turbulent.
Explained in: Stokes' law and settling velocity for metallurgists
- Rhodanine
An indicator that turns from yellow to salmon pink when excess silver is present.
Explained in: Free cyanide titration with silver nitrate: method and maths
- Richardson–Zaki equation
A correction for hindered settling based on the solids volume fraction.
Explained in: Stokes' law and settling velocity for metallurgists
- Rise rate
Overflow flow divided by thickener area (m/h).
Explained in: Thickener operation: bed, flocculant and rise rate
- Roasting
Heating a concentrate in air to oxidise sulphides and organic carbon.
Explained in: Roasting refractory gold: two-stage roasting and SO2
- ROM stockpile
Run-of-mine stockpile: ore stored between the pit and the crusher.
Explained in: Gold reconciliation: F-factors, GIC and scheduling
- Root cause
The underlying reason for a problem, which, if fixed, stops it recurring.
Explained in: Root cause analysis for metallurgical plant problems
- Roping
An overloaded apex discharging a thick rope of slurry, which forces coarse particles into the overflow.
Explained in: Hydrocyclone partition curve and d50 cut size explained
- Rosin–Rammler distribution
An equation describing a size distribution with a characteristic size and a uniformity coefficient.
Explained in: Particle size analysis and how to calculate P80
- Rotary divider
A splitter that feeds material onto rotating containers or a rotating cutter to divide it into equal parts.
Explained in: Sampling system design: cross-stream cutters explained
- Rougher
The first flotation stage, which aims to recover as much of the valuable mineral as possible at a moderate grade.
Explained in: Flotation kinetics test and rate constant calculation
S
- SAG mill
A semi-autogenous grinding mill, which uses the ore itself plus some steel balls as grinding media.
Explained in: Rapid Bond work index estimate for grinding circuit audits
- Saline water
Process water with a high dissolved salt content, which holds less oxygen.
Explained in: Dissolved oxygen in cyanide leaching: control and targets
- Sample station
The series of cutters and dividers that reduce a primary sample to a laboratory sample.
Explained in: Sampling system design: cross-stream cutters explained
- Sanding
Build-up of settled coarse solids on a tank floor.
Explained in: Agitator design for leach tanks: power, suspension
- SC6
Spodumene concentrate at about 6% Li₂O, the common traded product.
Explained in: Spodumene concentrate production: DMS and flotation to SC6, Heavy liquid separation test for spodumene ore
- Scale-up factor
The number laboratory time is multiplied by to give the design residence time of a plant bank.
Explained in: Flotation kinetics test and rate constant calculation
- Scalping screen
A screen that removes coarse material ahead of a concentrator.
Explained in: Gravity circuit design for gold: bleed and recovery
- Scavenger
A bank that recovers remaining valuable mineral from rougher tailings.
Explained in: Flotation circuit survey and mass balance guide
- Seepage
Water that leaves the storage facility through its base or walls.
Explained in: Plant water balance: tailings, decant and make-up water
- Settled dry density
Mass of tailings solids per cubic metre of settled tailings.
Explained in: Plant water balance: tailings, decant and make-up water
- Settling slurry
A slurry whose particles settle quickly when flow slows; most mill circuit slurries.
Explained in: Slurry pipeline critical velocity: Durand equation
How steep the partition curve is. A sharper cut sends fewer wrong-sized particles to each product.
Explained in: Hydrocyclone partition curve and d50 cut size explained
- Shear reactor
A device that dissolves oxygen into slurry under high shear and pressure.
Explained in: Oxygen uptake rate test for gold leach slurries
- Shift
A lasting change in the average of a process.
Explained in: CUSUM chart for plant recovery: method and worked example
- Short-circuiting
Pulp leaving a well-mixed cell sooner than average, so it has less chance to float.
Explained in: Flotation kinetics test and rate constant calculation, Flotation cell sizing calculation with worked example, CIL circuit model: tanks in series and carbon loading
- Short ton
2,000 lb, about 0.907 metric tonnes; Bond's original unit.
Explained in: Bond work index test: how to run it and calculate Wi
- Sieve analysis
Sorting a sample into size fractions with a stack of sieves and weighing each fraction.
Explained in: Particle size analysis and how to calculate P80
- Sieve series
A set of sieve openings stepping by a fixed ratio, usually about the square root of 2.
Explained in: Particle size analysis and how to calculate P80
- Sinks and floats
Particles heavier and lighter than the liquid.
Explained in: Heavy liquid separation test for spodumene ore
- Sintering
Partial melting and fusing of particles at high temperature, which can seal gold away from cyanide.
Explained in: Roasting refractory gold: two-stage roasting and SO2
- Size-by-size recovery
Recovery calculated separately for each particle size class.
Explained in: Flotation circuit survey and mass balance guide
- Slag
The glassy layer of oxides and flux that separates from molten bullion.
Explained in: Gold room operations: smelting and doré accounting
- Slurry
A mixture of solid particles and water, pumped as a fluid.
Explained in: Slurry pipeline critical velocity: Durand equation
- Slurry (pulp)
Finely ground ore mixed with water.
Explained in: Carbon-in-leach vs carbon-in-pulp: circuit choice and losses
- SMBS
Sodium metabisulphite, Na2S2O5, a solid source of sulphur dioxide.
Explained in: Cyanide destruction: SO2/air reagent calculation
- % solids
Mass of dry solids as a percentage of the mass of pulp.
Explained in: Ore specific gravity by pycnometer: method and formula
- Solids loading
Dry solids feed rate divided by thickener area (t/h per m²).
Explained in: Thickener operation: bed, flocculant and rise rate
- Solubility
The most of a gas or solid that a liquid can hold at a given temperature and pressure.
Explained in: Dissolved oxygen in cyanide leaching: control and targets
- Soluble loss
Dissolved gold that leaves with the tailings solution.
Explained in: CIL circuit model: tanks in series and carbon loading
- Solution-to-ore ratio
Total solution applied per tonne of ore (m³/t).
Explained in: Heap leach column test: procedure and scale-up
- Solvent extraction
Transferring a metal between an aqueous solution and an immiscible organic phase.
Explained in: Solvent extraction McCabe-Thiele diagram explained
- Solvent extraction (SX)
Transferring copper from the leach solution into an organic phase and then into a strong electrolyte.
Explained in: Copper heap leach and SX-EW: the key calculations
- Sparging
Bubbling air or oxygen into a tank.
Explained in: Dissolved oxygen in cyanide leaching: control and targets, Oxygen uptake rate test for gold leach slurries
- Specific cake resistance, α
How strongly a cake resists flow per kilogram of cake per square metre (m/kg).
Explained in: Filter leaf test: filtration rate and filter sizing
- Specific energy
Energy used per tonne of ore, in kWh/t.
Explained in: Rapid Bond work index estimate for grinding circuit audits, Electrowinning current efficiency and Faraday's law, Ore blending for the mill: grade and throughput
- Specific gravity
Density of a material divided by the density of water.
Explained in: Ore specific gravity by pycnometer: method and formula
- Split
Dividing a sample into a smaller, representative part with a riffle splitter or rotary divider.
Explained in: Gy's formula: minimum sample mass calculation explained
- Spodumene
A lithium aluminium silicate mineral, the main lithium mineral in Western Australian hard-rock deposits.
Explained in: Spodumene concentrate production: DMS and flotation to SC6, Lithium hydroxide from spodumene: process and LCE
- SP (setpoint)
The target value for the PV.
Explained in: Process control basics: PID loops and lambda tuning
- Standard deviation (σ)
A measure of how much a measurement typically scatters around the true value.
Explained in: Mass balance reconciliation explained: WLS and chi-square
- Standard deviation, σ
A measure of day-to-day scatter when the process is steady.
Explained in: CUSUM chart for plant recovery: method and worked example
- Standby
Time the plant could run but did not, for external reasons.
Explained in: Plant availability, utilisation and OEE explained
- Steady state
Plant conditions held constant so that flows and grades do not drift during sampling.
Explained in: Flotation circuit survey and mass balance guide
- Stockpile
A pile of mined ore held for later feeding, often by grade or ore type.
Explained in: Ore blending for the mill: grade and throughput
- Stock solution
A concentrated solution made in the mixing tank and stored for dosing.
Explained in: Reagent dosing calculation: g/t to pump flow
- Stoichiometric
The exact amount of reagent the chemical equation requires.
Explained in: Cyanide destruction: SO2/air reagent calculation
- Stokes' law
The settling velocity of a small particle in a fluid, proportional to its size squared and its density difference.
Explained in: Gravity concentration criterion and calculations, Stokes' law and settling velocity for metallurgists
- Sulphide oxidation
The percentage of sulphide sulphur converted to sulphate.
Explained in: POX and BIOX for refractory gold: oxygen and acid
- Superficial gas velocity (Jg)
Air flow divided by cell cross-sectional area.
Explained in: Flotation reagents, froth and gas dispersion explained
- Survey
A planned sampling campaign around a circuit at steady state.
Explained in: Flotation circuit survey and mass balance guide
T
- Tabular CUSUM
A form of CUSUM that resets to zero and gives a numerical alarm rule.
Explained in: CUSUM chart for plant recovery: method and worked example
- Tailings
The waste stream left after the valuable mineral has been removed.
Explained in: Metallurgical recovery calculation: 2- and 3-product methods
- Tailings storage facility (TSF)
The engineered structure that stores tailings solids and the water released from them.
Explained in: Plant water balance: tailings, decant and make-up water
- Target, T
The reference value the CUSUM measures departures from.
Explained in: CUSUM chart for plant recovery: method and worked example
- Terminal settling velocity
The steady speed a particle reaches when drag balances its weight in the fluid.
Explained in: Stokes' law and settling velocity for metallurgists
- Test (closing) sieve
The screen that defines 'fine enough' in the test; its aperture is P1.
Explained in: Bond work index test: how to run it and calculate Wi
- Thermal reactivation
Heating carbon in steam in a kiln to remove organic fouling and restore pores.
Explained in: Carbon regeneration kilns and carbon activity
- Thickener
A large settling tank that produces a thick underflow and clear overflow water.
Explained in: Thickener sizing: settling test and unit area calculation, Thickener operation: bed, flocculant and rise rate
- Thickener overflow
Clear water from the top of a thickener, usually returned to the process water tank.
Explained in: Plant water balance: tailings, decant and make-up water
- Thiocyanate
SCN⁻, formed when cyanide reacts with sulphur species; measured separately.
Explained in: Free, WAD and total cyanide explained
- Time constant
The time after the dead time for the PV to reach 63.2% of its final change.
Explained in: Process control basics: PID loops and lambda tuning
- Tip speed
The speed of the impeller blade tips: π × diameter × revolutions per second.
Explained in: Agitator design for leach tanks: power, suspension
- Titration
Adding a reagent of known strength from a burette until a colour change shows the reaction is complete.
Explained in: Free cyanide titration with silver nitrate: method and maths
- Titre
The volume of reagent used to reach the end point.
Explained in: Free cyanide titration with silver nitrate: method and maths
- Top size
The size that about 95% of particles pass.
Explained in: Sampling system design: cross-stream cutters explained
- Top size, d
The screen size that 95% of the material passes.
Explained in: Gy's formula: minimum sample mass calculation explained
- Total cyanide
All cyanide, including strong iron, cobalt and gold complexes, released by strong-acid distillation.
Explained in: Free, WAD and total cyanide explained
- Total organic carbon
An assay of carbon present as organic matter, a warning sign for preg-robbing.
Explained in: Diagnostic leach and preg-robbing test for gold ores
- Troy ounce
The unit for precious metals: 31.1035 g.
Explained in: Gold room operations: smelting and doré accounting
- Two-stage roasting
A first stage short of oxygen to remove arsenic, then a second stage with excess air.
Explained in: Roasting refractory gold: two-stage roasting and SO2
U
- Umpire laboratory
An independent laboratory used to check the main laboratory.
Explained in: Assay QAQC: standards, blanks and duplicates explained
- Unaccounted metal
Check-in minus check-out and the change in inventory.
Explained in: Month-end metal accounting: check-in vs check-out
- Underflow
The coarse product leaving the bottom (apex) of the cyclone; in a grinding circuit it returns to the mill.
Explained in: Hydrocyclone partition curve and d50 cut size explained, Thickener sizing: settling test and unit area calculation
- Undersize
Material that passes through the openings.
Explained in: Screen efficiency calculation with worked example
- Unit area
The thickener floor area needed per tonne of dry solids per day (m² per t/d).
Explained in: Thickener sizing: settling test and unit area calculation
- Unit recovery
The share of GRG a concentrator recovers from the feed it receives on one pass.
Explained in: Gravity circuit design for gold: bleed and recovery
- Unleachable residue
Gold that does not dissolve however long it is leached, for example gold locked in sulphides.
Explained in: CIL circuit model: tanks in series and carbon loading
- Utilisation
The share of calendar time the plant actually ran.
Explained in: Plant availability, utilisation and OEE explained, Crushing circuit design: rates, screens and stockpiles
V
- Variability
How much grade or hardness changes from hour to hour or day to day.
Explained in: Ore blending for the mill: grade and throughput
- Viscosity
A fluid's resistance to flow; water is about 1 mPa·s at 20 °C.
Explained in: Stokes' law and settling velocity for metallurgists
W
- WAD cyanide
Weak acid dissociable cyanide: free cyanide plus cyanide in weak and moderately strong metal complexes.
Explained in: Free cyanide titration with silver nitrate: method and maths, Cyanide destruction: SO2/air reagent calculation, Free, WAD and total cyanide explained
- Washability curve
Cumulative grade and recovery of the sinks plotted against separation density.
Explained in: Heavy liquid separation test for spodumene ore
- Water balance
An account of all water entering and leaving a plant or site, including changes in storage.
Explained in: Plant water balance: tailings, decant and make-up water
- Water bypass, Rf
The fraction of feed water that goes to the underflow, carrying unclassified fines with it.
Explained in: Hydrocyclone partition curve and d50 cut size explained
- Water commissioning
Running systems on water to test equipment, controls and interlocks under realistic conditions.
Explained in: Process plant commissioning: phases, tools and checklists
- Wear rate
Steel lost from the balls per unit of energy (kg/kWh) or per tonne of ore (kg/t).
Explained in: Grinding ball size and ball wear rate calculation
- Weighted least squares
A method that finds the smallest set of adjustments, weighted by each measurement's uncertainty, that makes the balance close.
Explained in: Mass balance reconciliation explained: WLS and chi-square
- Weightometer
A belt scale that weighs ore on a moving conveyor.
Explained in: Mass balance reconciliation explained: WLS and chi-square
- Wet screening
Washing fines through the finest sieve before dry sieving.
Explained in: Particle size analysis and how to calculate P80
- WHIMS
Wet high-intensity magnetic separator, using a magnetised steel matrix to catch weakly magnetic particles.
Explained in: Magnetic separation and the Davis tube test
- Work index (Wi)
The energy needed to grind an ore from a large size to 80% passing 100 µm, in kWh/t.
Explained in: Bond work index test: how to run it and calculate Wi
- Work index, Wi
A measure of how hard an ore is to grind, from Bond's laboratory test (kWh/t).
Explained in: Ball mill sizing: Bond energy and Rowland factors
- % w/v
Grams of reagent per 100 mL of solution.
Explained in: Reagent dosing calculation: g/t to pump flow
- % w/w
Grams of reagent per 100 g of solution.
Explained in: Reagent dosing calculation: g/t to pump flow
Z
- Zadra
Elution with hot caustic cyanide solution recirculating through the column and electrowinning cells.
Explained in: Carbon elution: AARL vs Zadra, with calculations
- Zinc dust
Very fine zinc powder used to precipitate gold and silver.
Explained in: Merrill-Crowe process: zinc precipitation of gold