Tiegel home Talk to a metallurgist

Month-end metal accounting: check-in, check-out, unaccounted metal and the AMIRA P754 code

The month-end close at a processing plant: check-in and check-out, change in gold in circuit, unaccounted metal, calculated head and the principles of the AMIRA P754 code.

· 4 minute read · By

At the end of each month a processing plant must report the metal it received, the metal it produced and the metal it still holds, and these three figures should balance. The difference, when they do not, is unaccounted metal. The purpose of metal accounting is to keep it small, explain it and demonstrate that the figures are reliable.

The figures are used well beyond the plant, in company reports, royalty calculations, reconciliation with the mine and, for listed companies, public statements to investors.

This article covers the month-end calculations and the principles of good practice. Reconciliation factors and gold-in-circuit methods are covered in gold reconciliation and gold in circuit, and the balancing calculations in mass balance reconciliation.

Month-end metal accounting cycleMeasurements are collected and checked, inventories surveyed, the metal balance calculated, check-in compared with check-out, differences investigated, and the report signed off.Collect andcheck dataSurveyinventoriesMetalbalanceCheck-in vscheck-outInvestigatedifferencesReport andsign offevery figure traceable to its source: weigher, sample, assay, survey
The month-end cycle. Most of the work is in the first two boxes: a balance is only as good as the measurements and inventories behind it.

Check-in, check-out and unaccounted metal

unaccounted=check-in−(check-out+Δinventory)calculated head=gold out+Δinventorydry tonnes treated

where

check-in
metal into the plant, from feed tonnes and feed assays
check-out
metal leaving: product sold or poured plus tailings
Δinventory
increase in metal held in the plant, such as gold in circuit (negative if it fell)

Worked example, one month at a gold plant:

ItemBasisGold (oz)
Check-in: mill feed250,000 dry t at 1.62 g/t (feed sampler)13,021
Gold pouredBullion, refinery-settled11,250
Tailings250,000 t at 0.16 g/t (tails sampler)1,286
Increase in gold in circuitSurvey at start and end of month240
Unaccounted13,021 − (11,250 + 1,286 + 240)245 (1.9%)
One month's gold balance (troy ounces)Gold in feed 13,021 ounces; poured 11,250; in tailings 1,286; increase in gold in circuit 240; unaccounted 245.Check-in: gold in feedCheck-in: gold in feed: 13,02113,021Gold pouredGold poured: 11,25011,250Gold in tailingsGold in tailings: 1,2861,286Increase in gold in circuitIncrease in gold in circuit: 240240UnaccountedUnaccounted: 245245Gold (oz)
Check-out plus the change in inventory explains 98.1% of the gold measured in. Whether a 1.9% gap is acceptable depends on the precision of the feed sampling. Illustrative figures.

The calculated head is (11,250 + 1,286 + 240) × 31.1035 ÷ 250,000 = 1.59 g/t, 98.1% of the assayed 1.62 g/t. Recovery on the calculated head is (11,250 + 240) ÷ 12,776 = 89.9%, whereas on the assayed head it would be 88.2%. Sites must state the basis on which they report.

Assessment of unaccounted metal

Every figure in the balance carries error. The poured gold, weighed and assayed by a refinery, is usually the most precise; feed and tailings sampling, belt weighers and gold-in-circuit surveys are much less so. The precision of each is estimated, the estimates are combined, and the unaccounted metal is compared with the combined error. A difference well within it is noise. A difference outside it, or one with the same sign month after month, indicates a bias that must be located, such as a belt weigher out of calibration, a sampler that misses part of the stream, or an inventory that is not being measured correctly.

The AMIRA P754 Code of Practice

The AMIRA P754 Code of Practice for Metal Accounting is the industry reference for good practice. It is not mandatory, but many companies and auditors use it as the standard. Its principles include:

  • accurate mass measurement and a component balance, with a check-in/check-out approach on final products;
  • consistent, transparent and documented procedures that do not depend on one person;
  • target accuracy levels for the principal measuring and sampling points;
  • regular stockpile and inventory surveys, with documented assumptions;
  • identifying and minimising bias;
  • timely results, sign-off for any replaced or estimated data, reconciliation, and regular internal and external audit.

Month-end checklist

  • Close off weigher totals and check calibrations and zero checks for the month.
  • Confirm that all assays have been received and that standards, blanks and duplicates passed; see assay QAQC.
  • Survey gold in circuit, stockpiles and any other inventory at the same cut-off time.
  • Run the balance, compare check-in with check-out, and compare calculated with assayed head.
  • Investigate, document and sign off any replaced or estimated data.
  • Issue the report with the basis of each figure stated.

Glossary

Metal accounting
Measuring and reporting the metal received, produced and held by a plant over a period.
Check-in
Metal entering the plant, measured from feed tonnes and assays.
Check-out
Metal leaving the plant in products and tailings.
Unaccounted metal
Check-in minus check-out and the change in inventory.
Calculated head
Feed grade back-calculated from products, tailings and inventory change.
Gold in circuit
Gold held in the plant at a point in time, in solution, on carbon and in other inventories.
AMIRA P754
An industry code of practice for metal accounting.
Bias
A consistent error in one direction, as opposed to random error.

Frequently asked questions

What is unaccounted metal?

Check-in less check-out and the change in inventory. In the example, 13,021 oz in, 12,536 oz out and 240 oz added to inventory leave 245 oz, or 1.9%, unaccounted.

Is a 2% unaccounted difference acceptable?

It depends on the precision of the measurements. It should be compared with the combined error of feed sampling, weighing, tailings sampling and inventory surveys. A difference that always has the same sign suggests a bias.

Should recovery be reported on calculated or assayed head?

Either may be used, but the basis must be stated. The two differ by the unaccounted metal, which is why the basis matters.

Is the AMIRA P754 code mandatory?

No. It is a voluntary code of practice, but it is widely used by companies and auditors as the reference for good metal accounting.

Discuss your plant with a metallurgist

Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.

Talk to a metallurgist

References and further reading

  1. Power, D.P. (2010). The application of the AMIRA P754 metal accounting code in the coal industry. Journal of the Southern African Institute of Mining and Metallurgy, 110, July 2010. Link
  2. Applying the AMIRA P754 Code of Practice for Metal Accounting. Metplant 2008, AusIMM. Link
  3. Wills, B.A. and Finch, J.A. (2016). Wills' Mineral Processing Technology, 8th edition. Butterworth-Heinemann. Chapter 3, Metallurgical accounting, control and simulation.

Worked examples and charts marked illustrative use invented figures, not data from any operation.